Response RE3000S Instrucciones de operaciones descargar pdf (Pagina 26)

24 RE5000S Professional Alarm System

TROUBLE SHOOTING

Control Unit will not arm. Control Unit

emits 3 bleeps when trying to arm.

1. Magnetic Contact Detector ‘Open’ - Check Zone

LED illuminated and close detector(s) on that Zone.

If Detector cannot be closed, enter, then exit

Programming mode to clear the indication.

2. Low battery in a Detector. Check Zone indicated,

change battery and clear indication at Control Unit.

3. Alarm/low battery indicator not cleared. Enter Main

User or Second User Access Code followed by .

Detection Zone has been triggered but no

alarm is sounding

1. Entry delay zone triggered - alarm will sound when

delay time has expired.

2. Zone omitted when part armed.

3. Silent alarm option selected.

Control Unit ‘Low Battery’ light flashing,

Zone LED(s) flashing and control unit

bleeping every 60 seconds

1. Check all PIR Detector(s) on the Zone indicated for

low battery, indicated by detector LED flashing when

movement is detected - change battery(s) as

required.

2. Check all Magnetic Detectors on the Zone indicated

for low battery indicated by detector LED not

illuminating when detector is opened/closed -

change battery(s) as required.

3. Check the battery in all RE5000 Smoke Detectors -

a low battery will also cause the Smoke Detector to

bleep every minute - change battery as required.

Full Alarm Occurs when alarm has not been

activated by an intruder

1. Ensure mains adaptor is plugged in/connected and

switched on.

2. Ensure that the Control Unit is securely fitted to the

wall and that the rear battery compartment cover is

closed.

3. Check that Personal Attack Button, Medical Alert

Pendant or Smoke Detectors have not been

operated.

4. Check that battery covers on all detectors are fitted

securely.

5. Check for Jamming Detection Alarm operation.

Control Unit not working. Mains light is off.

1. Check that mains adaptor is plugged in/connected

and switched on.

Control Unit will not function

(Sirens are sounding)

1. Disconnect power (including Control Unit back-up

battery), for 10 seconds, then re-connect mains

power followed by back up battery. (Remember, all

programmed functions will be retained if the Memory

Link is in the ‘ON’ position).

Control Unit not accepting access code(s).

1. Pausing too long between pressing keys. Do not

pause for more than 5 secs between keys.

2. Incorrect code entered. Allow 5 seconds to elapse

before re-entering correct code.

3. Unit has reset to factory default codes/programme.

Fit Memory Link in ‘ON’ position and re-programme

all programmable features.

Control Unit emits two-tone chime when

detectors are triggered.

1. Door-Chime set to operate on Magnetic Detector

Zone(s) - Re-programme Door-Chime Zone(s).

2. Control Unit in ‘Test’ mode - Reset to normal,

disarmed mode.

Control Unit not responding to detectors.

1. Ensure detectors are within radio range of Control

Unit. If not, move detector closer.

2. Ensure that the ‘House Code’ on the Detector is the

same as that set in the Control Unit.

3. Replace detector battery.

Solar Siren and Strobe sounding but no

alarm at Control Unit.

1. Siren Anti-tamper activated. Check security of

Siren/Strobe fixing to wall and that Siren anti-tamper

switch is fully depressed.

2. Siren & Strobe has not received ‘Stop’ signal.

Press Disarm on Remote Control to make the

Control Unit re-transmit the ‘Stop’ signal.

Symptom

Recommendation Symptom

Recommendation

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Comentarios a estos manuales

Sin comentarios

Response RE3000S Instrucciones de operaciones Pagina 26

Comentarios a estos manuales