Response SA5 E Instrucciones de operaciones Pagina 30
- Pagina / 44
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Tel Confirm Times
This sets the number of acknowledged phone numbers
required to stop the voice dialler. For example if set to
"2" then the dialing sequence will continue until an
acknowledgment is received from two different
n
umbers, (e.g. Phone No.1 and Phone No.3).
Default setting: 1
Scroll through the menu until ‘4-6 Tel Confirm Times’ is
displayed. The current settings will also be displayed.
To change the setting press .
Enter the required number (1-4).
Press to save and exit, or
Press to exit without saving.
Call Attempts
This sets the maximum number of times that the
dialler will attempt to contact each enabled telephone
number in the call routing sequence.
Default setting: 3
Scroll through the menu until ‘4-7 Call Attempts’ is
displayed. The current settings will also be displayed.
To change the setting press .
Enter the required number (1-5).
Press to save and exit, or
Press to exit without saving.
Full Arm Setup
Scroll through the programming menu until ‘5. FULL
ARM SETUP’ is displayed and press .
N
ote: After configuring Full Arm press to return
to the top level programming menu.
Exit Delay
S
croll through the menu until ‘5-1 EXIT-DELAY’ is
displayed. The current settings will also be displayed.
T
o change the settings press .
On/Off Status
Default setting: ON
Scroll through the menu until ‘5-1-1 Status’ is
displayed. The current setting will also be displayed.
To change the settings press .
Press to enable the Exit delay, or
Press to disable the Exit delay.
Delay Period
Default setting: 30 seconds
Scroll through the menu until ‘5-1-2 Delay Time’ is
displayed. The current settings will also be displayed.
To change the settings press .
Enter the required delay period (10 to 250s).
Press to save and exit, or
Press to exit without saving.
Press to return to top level Full Arm Setup
menu.
Entry Delay Beep
This controls the warning beep which operates during
the Entry Delay period when Full Arm is active.
Default Setting: ON
Scroll through the menu until ‘5-2 Entry Delay Beep’ is
displayed. The current setting will also be displayed.
To change the setting press .
Press to enable the entry-delay beep, or
Press to disable the entry-delay beep.
30
ESC
ESC
ESC
5. FULL ARM
SETUP
PROGRAM MODE
Code:
5-3 Exit Delay
Beep: xxx
5-2 Entry Delay
Beep: xxx
Select
ON->1 OFF->3
Select
ON->1 OFF->3
5-1 EXIT Delay
xxx xxxs
5-1-1 Status
xxx
Select
ON->1 OFF->3
5-1-2 Delay Time
Enter (10-250s)
Enter (10-250s)
1
3
1
3
ESC
ESC
- 36 Zone Wirefree Alarm System 1
- Contents 2
- Kit Contents 3
- Introduction and Overview 4
- Switch 1 6
- = set to ON 6
- position 6
- Control Panel 8
- Remote Control Unit 10
- Passive Infrared (PIR) 11
- Movement Detectors 11
- PIR Movement Detectors 12
- Testing the PIR Detectors 13
- Magnetic Contact 14
- Detectors 14
- External Solar Siren 15
- Positioning the Solar Siren 16
- Installing the Solar Siren 16
- Setting the Solar Siren 16
- Alarm Duration Limit 17
- Beep Disable 17
- Siren Disable 17
- External Connections 18
- Testing the System 18
- Walk Test 19
- Alarm Test 19
- Wirefree Siren Service ON/OFF 19
- Voice Dialler Test 19
- Digital Dialler Test 19
- Factory Default Settings 20
- OFF ON 21
- Programming Instructions 22
- System Setup 23
- Call Abort 25
- Dial Method 25
- Dial Mode 25
- Zone Setup 26
- Final Exit Set 27
- Entry Delay 27
- Part-Arm 1 27
- Voice Dialler Setup 28
- Alarm Message Play Time 29
- Record Alarm Messages 29
- Replay Alarm Messages 29
- Call Routing 29
- Full Arm Setup 30
- Part-Arm 1 Setup 31
- Part-Arm 2 Setup 32
- Time & Date Setup 32
- Latch Key Setup 33
- Home Automation Setup 34
- Answer Phone Setup 34
- Remote Manager Setup 34
- Operating Instructions 35
- Remote Control: 36
- Control Panel: 36
- Voice Memo 37
- Replay Messages 37
- Remote System Control 37
- Battery Monitoring 38
- Maintenance 39
- Alarm Record 40
- Troubleshooting 41
- Symptom 42
- Recommendation Symptom 42
- Recommendation 42
- Extending your Alarm System 43
- Component Specification 44
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Response SA5 E
Los Sistemas De Control De Acceso De Seguridad Response SL2 Instrucciones de operaciones
(28 paginas)
(28 paginas)
Los Sistemas De Control De Acceso De Seguridad Response SL5 Instrucciones de operaciones
(52 paginas)
(52 paginas)
Los Sistemas De Control De Acceso De Seguridad Response SA2 E Instrucciones de operaciones
(24 paginas)
(24 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales